1.The ratio of voltage and electric current in a closed
circuit
(a) remains constant (b) varies (c) increases (d) falls
2.The resistance of a wire varies inversely as
(a) area of cross section (b) length (c) resistivity (d)
temperature
3.The electrical conductivity of metals is typically of the
order of ( in
ohm-1 m-1)
(a) 10 to the power of 7 (b) 10 to the power of 5 (c) 10 to the
power of -4
(d) 10 to the power of -6
4.Four resistors, each of resistance R ohms are available.
The minimum
resistance of the combination will be
(a) 4R (b) R (c) R/4 (d) R/8
5.The elements which are not capable of delivering energy by
its own are
known as
(a) unilateral elements (b) non-linear elements (c) passive
elements (d)
active elements
6.The magentic susceptibility of paramagnetic material is
(a) less than zero (b) less than one but positive (c)
greater than one (d)
equal to zero
7.The Direction of current in an ac circuit
(a) is from positive to negative (b) is always in one
direction (c) varies
from instant to instant (d)Cannot be determined
8.which of the following statements associated with purely
resistive
circuits is correct?
(a) PF is unity (b) Power consumed is zero (c) Heat produced
is zero (d) PF
is zero
9.The magnetic field energy in an inductor changes from
maximum value to
minimum value in in 5m sec when connected to an ac source.
The frequency of
the source is
(a) 20 Hz (b) 50 Hz (c) 200 Hz (d) 500 Hz
1.Electronic control systems have the serious draw-backs of
(a) low reliability (b) operational difficulty (c)
temperature
sensitiveness (d) all of above
2.The system whose characteristic equation has the following
roots is
marginally stable
(a) -j, j, -1,1 (b) -3,-2,0 (c) -2+3j, -2-3j, -2 (d)
-3,-2,-1
3.A phase log compensation will
(a) improve relative stability
(b)increase the speed of response
(c)increase band-width
(d) increase overshoot
4.For Nyquist plot we use
a.open loop function
b.closed loop function
c.characteristic equation
d.any of the above
• A system with gain
margin close to unity or a phase margin close to zero is
a.highly stable
b.oscillatory
c.relatively stable
d.none of these
• Root locus diagram
exhibits the
a.frequency response of a system
b.poles of the transfer function for a set of parameter
values
c.bandwidth of system
d.all of the above
• Increase in the
gain K makes the system
a.more stable
b.unstable
c.none of above
• The transfer
function of a system is used to determine
a.the output for a given input
b.the type of system
c.the input for a given output
d.the steady state gain
• In a servo system
the voltage induced in the control transformer rotor
is the
a.error voltage
b.driving voltage
c.opposing voltage
d.none of these
• With the feedback
system, the transient response
a.decays slowly
b.decays rapidly
c.rises slowly
d.rises quickly
Measurements and Instrumentation
1.Which of the following types of instrument is an
integrating instrument?
a.power factor meter
b.energy meter
c.wattmeter
d.frequent meter
• Which of the
material is used for the ’swamping’ resistance that is
connected in series with the working coil of a voltmeter?
a.Constantan
b.Manganin
c.Eureka
d.Nichrome
• What are used to
increase the range of ammeters.
a.Multipliers
b.Shunts
c.Control Springs
d.Potential transformers
• Which voltmeter do
you select for measuring 50KV DC?
a.Moving Coil Voltmeter
b.Hot wire voltmeter
c.Electro Dynamo meter
d.Electrostatic Voltmeter
• Which of the
following you will prefer to extend the range of an ac
voltmeter?
a.Low series resistance
b.high resistance in parallel
c.CT
d.PT
• High AC voltages
are usually measured with
a.magnetic voltmeter
b.inductive voltmeter
c.potential transformers with voltmeters
d.current transformers and voltmeters
• Creeping is the
phenomena occurs in
a.voltmeter
b.wattmeter
c.energy meter
d.ammeter
1.Which of the following is not a Primary Energy Source?
a) Oil b) Natural
Gas c) Electricity d) Wood
2.Which of the following is a renewable energy source?
a) Bitumen b)
Solar Energy c) Coal d) Natural Gas
3.Which of the following States in India does not have
proven coal reserve?
a) Andhra Pradesh b)
Madhya Pradesh c) Kerala d) West Bengal
4.At present the share of
hydro power in the country’s total generated
units is around
a) 20% b) 25% c) 30%
d) 35%
5.Greenhouse effect refers to increase in
a)Global temperature.
b) Carbon monoxide c) atmospheric pressure
d) Greenery
6.The nodal agency for coordinating the energy conservation
activities
under EC act in India is
a) Bureau of Indian
Standards b) Bureau of Energy
Efficiency
c) Bureau of Energy Education d) Bureau of Energy and Environment
7.X-Ray is a form of
a.Chemical Energy
b.Radiant Energy
c.Thermal Energy
d.Potential Energy
8.Ratio of maximum demand to connected load is termed as:
a.Load factor
b.Power factor
c.Demand factor
d.Form factor
9.When heat is added or subtracted, resulting in a change of
temperature is called as
a.Sensible heat
b.Latent heat
c.Specific heat
d.Heat capacity
10.The objective of energy management is
a)To minimize energy costs
b)To minimize environmental effects
c)a & b
d)None of the above
11.For calculating plant energy performance which of the
following data
is not required
a)Current year’s production
b)Reference year production
c)Reference year energy use
d)Capacity utilization
12.The simplest technique for scheduling of tasks and
tracking the
progress is
a)Gantt chart b)
CPM c) PERT d) CUSUM
13.Moderation of chilled water temperature for process is
a)Matching energy usage to requirement
b)Increasing system efficiency
c)None of the above
d)a & b
14.Which of the
following is used to represent energy balance of a system?
a) Sankey Diagram
b) Flow Chart
c) Single line Diagram
d) Block Diagram
15.Among the following, which is most important for carrying
out a
material balance
a)Temperature of
Products
b) Mass
c ) Waste Quantity
d) Pressure
16.In PV = nRT, Value
of R
is
a)0.008206 m3 atm / mole K
b)0.8206 m3 atm / mole K
c)0.08206 m3 atm / mole K
d)0.09206 m3 atm / mole K
17.Energy available in fuels is stored as
a)Heat Energy b)
Chemical Energy c) Atomic Energy d) Explosive Energy
18.In continuous process which is considered for carrying
out mass balance
a) Material Flow
b) Time c)
Both a and b d) None of the
above
19.Reactive Power is required for
a.Inductive load
b.Resistive load
c.Capacitive load
d.All of the above
20.In a purely resistive circuit the reactive kVAR will be
a) less than 1 b)
more than 1 c) zero d) one
21.Which one is the key element for successful Energy
Management?
a) Top management support
b) Planning c) Monitoring d) Training
22.Capital costs are the costs associated with
a)Design
b)Installation & Commissioning of project
c)a & b
d)Savings from project
23.What is the NPV of a project , (life 2 year) which requires an
investment of Rs.50000 & yield Rs.30000 in the 1st year
and Rs.40000/- in
the next year, if the interest rate is 10%
a)10330
b)(10330)
c)20660
d)(30660)
24.Which is not a general practice of financing in-house
energy management
a)From a central budget
b)Bank loan
c)Money from stock market
d)Hire purchase
25.The first step in a project development cycle is
a) Identify components of the project b) Implement the project c) arrange
finance d) Training
26.For an investment which has a fluctuating savings over
its project
life which of these analysis would be the best option
a) Payback b)
NPV c)ROI d) IRR
27.What is the future value of Rs.1000/- after 3 years if
the interest
rate is 10%?
a)1610
b)3221
c)1331
d)2420
28.If asset depreciation is considered, then tax cash flow
would be
a)Higher
b)Lower
c)No effect
d)None of these
29.ESCO stands for
a) Energy supply company b) Energy service company c) Energy
standards
company d) Energy sourcing company
30.Which of the following is not an external source of fund
a) Bank loans
b) Leasing
arrangement
c) Revenue budget
d) Private Finance
31.Event in a project network diagram represents
a) Task
b) Milestone
c) a & b
d) none of the above
32.The essential elements of
monitoring and targeting system is
a) Recording
b) Reporting c) Controlling d) All the above
33.Which is not a green house gas
a) Methane b)
Nitrous oxide c) Carbon di oxide d)
Sulphur di oxide
34.If LPG has GCV of 12000 Kcal / kg, then 12 KWh is
equivalent to
--------kg LPG
a) 0.96 b) 0.86
c) 8.6 d)
86
35.Percentage share of different energy consumption in
an industry can
be best shown by a
a) Pie Chart b)
Bar Chart c) Line Diagram
36.A mass balance for energy conservation does not consider which of the
following
a) steam b) water c) raw materials d) lubricating oil
37.In the equation, Energy consumed = C + (M x Production) , where ‘C’ is
a) Variable energy consumption b) Fixed energy consumption
c) Specific energy Consumption d) None of the above
38.Based on the following Net present values, which of the
projects is
attractive for investment
a) –2199 b) + 23 c) 0
d) +13
39.While plotting a ‘CUSUM Chart’, it is observed that
“CUSUM’ during
previous month was 8, the same during this month will be
a) 
8 b)  8 c) = 8 d) Can’t be said
40.Specific energy Consumption can be expressed in which of
the following
units.
a) Tone / Kwh b)
KCal / Kg c) Kcal / Kwh d)
None of the
above
41.The Ozone layer in the atmosphere acts as an efficient
filter for
a) X-Rays b) UV-A Rays
c) UV-B Rays d) Intra red
Rays
42.Which of the following does not damage ozone layer?
a) CFC b) CCl3
c) HCFC d) HFC
43.Which gas causes global warming among the following?
a) CFC b) SO2 c)
O2 d) Argon
44.Ozone has
a) Three oxygen
atoms b)
Two oxygen atoms c) Two chlorine atoms d)
Two bromine atoms
45.GHG emissions are presented in ------------ Units
a) MMTOE b) MMTCE c) MMTME d) MMT
46.The major source of electrical power generation in India
is
a) thermal b) Hydel c) Nuclear d) Wind
47.The quantity of heat required to raise 1 kg of a
substance by 1oC is
known as
a) sensible heat b)
specific heat c) latent heat d) calorie
48.Matching energy
use to requirement means providing
a) just
theoretical energy needed b)
just the designers’ needs c)
energy with minimum losses
d) less than what is needed
49.The internal rate of return is the discount rate for
which the NPV is
a) Zero b) +ve c) –ve d) Less than 1
50.The monthly electricity bill for a plant is Rs. 10 lakhs
and accounts
for 38% of the total energy bill. The annual energy bill for the company
a) Rs. 315 lakhs
b) Rs. 26 lakhs c) Rs.
38 lakhs d) Rs. 380 lakhs
Section - II: SHORT DESCRIPTIVE QUESTIONS Marks: 10 x 5
= 50
(i) Answer all Ten questions
(ii) Each question carries Five marks
1What are the immediate term energy strategies recommended?
The immediate term energy strategies recommended are:
•Rationalizing the tariff structure of various energy
products
•Optimum utilization of existing assets
•Efficiency in production systems and reduction in
distribution losses,
including those in traditional energy sources.
•Promoting R & D, transfer and use of technologies and
practices for
environmentally sound energy systems, including new and
renewable energy
sources.
2 A 3  AC Load draws 8 KW power at 400 V supply voltage and 15 A line
current. Calculate
the power factor of the load.
Supply Voltage of the System (VL) = 400
Line Current (IL) -=15 A
Apparent Power = 3
x VL x IL
= 3 x 0.400 x 15
= 10.392 KVA
Active Power = 3
x VL x IL x (Cos ) KW
Given, active power of the Load = 8 KW
Hence, 10.392 COS  = 8 KW
3How benchmarking of energy consumption internally and
externally may be
useful.
Benchmarking of energy consumption internally and externally
(historical/trend analysis) are two powerful tools for
performance
assessment and logical evolution of avenues for improvement. Historical
data well documented helps to bring out energy consumption
and cost trends
month-wise/day-wise trend
analysis of energy consumption, cost, relevant
production features, specific energy consumption help to
understand effects
of capacity utilization on energy use efficiency and costs on a broader scale.
4Why steam is used as a popular mode of conveying energy?
The following characteristics of steam make it very popular
and useful to
convey energy in the industries.
•High Specific heat and latent heat
•High heat transfer coefficient
•Easy to control and distribute
•Cheap and inert
5In a chlora-alkali
plant, the inlet brine concentration to cell house
is 300 gpl and the outlet concentration is 260 gpl. If 3
MT Salt is added
per hour, find out the brine flow rate to the Cell House.
Answer :
Inlet concentration of
brine = 300 gpl
Outlet concentration of brine = 260 gpl
Salt consumption per litre of Flow
= (300-260) gm
=
40 gm
= 0.040 Kg
For 3 MT/hr Salt consumption, flows =
3 x 1000 Kg /hr
----------------------
0.040 Kg/lit
=
75,080 Lit/hr
= 75 m3/hr
6What are the duties and responsibilities (five each) of
Energy Manager as
per the Energy Conservation Act 2001?
Responsibilities
•Prepare an annual activity plan and present to management
concerning
financially attractive investments to reduce energy costs
•Establish an energy conservation cell within the firm with
management’s
consent about the mandate and task of the cell.
•Initiate activities to improve monitoring and process
control to reduce
energy costs.
•Analyze equipment performance with respect to energy
efficiency
•Ensure proper functioning and calibration of
instrumentation required to
assess level of energy consumption directly or indirectly.
Duties
•Report to BEE and State level Designated Agency once a year
the
information with regard to the energy consumed and action
taken on the
recommendation of the accredited energy auditor, as per BEE
Format.
•Establish an improved data recording, collection and
analysis system to
keep track of energy consumption.
•Provide support to Accredited Energy Audit Firm retained by
the company
for the conduct of energy audit
•Provide information to BEE as demanded in the Act, and with
respect to
the tasks given by a mandate, and the job description.
•Prepare a scheme for efficient use of energy and its
conservation and
implement such scheme keeping in view of the economic
stability of the
investment in such form and manner as may be provided in the
regulations of
the Energy Conservation Act.
7Explain Net Prevent Value and how NPV is calculated.
Net Present Value:
The net present value (NPV) of a project is equal to the sum
of the present
values of all the cash flows associated with it.
Where NPV = Net Present Value
CF t
= Cash flow occurring at the end
of year ‘ t ‘ (t
= 0,1, ….n)
n = Life of the project
k =
Discount rate
The discount rate (k) employed for evaluating the present
value of the
expected future cash flows should reflect the risk of the
project.
8 Define project and mention various steps involved in
Project Management
A project is a temporary endeavor undertaken to create a
unique product or
service. A project is
temporary in that there is a defined start (the
decision to proceed) and a defined end (the achievement of
the goals and
objectives)
Steps in Project Management:
The various steps in a project management are:
a)Project definition and scope
b)Technical Design
c)Financing
d)Contracting
e)Implementation
Performance Monitoring
9Calculate fixed energy consumption for a rolling mill
consuming 3,00,000
units electricity to produce 500 MT product per month and
having specific
energy consumption of 500 Kwh/MT.
Total energy consumed = Fixed Energy Consumption + (Specific
Energy
Consumption x Production)
Fixed energy consumption
= Total energy consumed – (Specific energy
consumption x
Production)
Given,
Total Energy Consumption = 3,00,000 Kwh
Specific energy Consumption
= 500 Kwh / MT
Total Production
= 500 Mt
Fixed Energy Consumption
= 300000 – (500 x 500)
= 5000 Units
10.Explain briefly about Emission Trading?
Article 17 of the Kyoto protocol opens up for emissions
trading between
countries that have made commitments to reduce greenhouse
gas emissions.
The countries have option to delegate this right of
emissions trading to
companies or other organizations.
In a system for emissions trading, the total amount of
emissions permitted
is pre-defined. The
corresponding emissions allowances are then issued to
the emitting installations through auction or issued
freely. Through
trading, installations with low costs for reductions are
stimulated to make
reductions and sell their surplus of emissions allowances to
organizations
where reductions are more expensive. Both the selling and
buying company
wins on this flexibility that trades offers with positive
effects on
economy, resource efficiency and climate. The environmental advantage is
that one knows, in advance, the amount of greenhouse gases
that will be
emitted. The
economical advantage is that the reductions are done where
the reduction costs are the lowest. The system allows for a cost effective
way to reach a pre-defined target and stimulates
environmental technology
development.
Section - III: LONG DESCRIPTIVE QUESTIONS Marks: 5 x
10 = 50
(i) Answer all Five questions
(ii) Each question carries Ten marks
1.Explain in detail the difference between Energy
Conservation and Energy
efficiency and its relevance
Energy Conservation and Energy Efficiency are separate, but
related
concepts. Energy
conservation is achieved when growth of energy
consumption is reduced, measured in physical terms. Energy Conservation
can, therefore, be the result of several processes or
developments, such as
productivity increase or technological progress. On the other hand Energy
efficiency is achieved when energy intensity in a specific
product, process
or area of production or consumption is reduced without
affecting output
consumption or comfort levels.
Promotion of energy efficiency will contribute to energy
conservation and
is therefore an integral part of energy conservation
promotional policies.
Energy efficiency is often viewed as a resource option like
coal, oil or
natural gas. Energy
efficiency provides additional economic
value by
preserving the resource base and reducing pollution. For example,
replacing traditional light bulbs with Compact Fluorescent
Lamps (CFLs)
will use only ¼ of
the energy to light a room.
Apart from the economic benefits, energy conservation and
energy efficiency
measures would assist in controlling the CO2 emission.
2.Explain in detail the methodology for conducting a
detailed energy audit.
A detailed energy
audit is carried out in three phases:
a)Pre-audit phase
b)Audit phase &
c)Post Audit phase
Pre Audit Phase:
A structured methodology to carryout an energy audit is
necessary for
efficient working. An
initial study of the site is essential, which will
give an energy auditor an opportunity to meet the personnel
concerned to
familiarize the site and assess the procedures necessary to
carry out the
energy audit. The
main aim of this visits are:
•To identify the main energy consuming areas/plant items to
be surveyed
during the audit.
•To identify any existing instrumentation/additional
metering required
•To decide whether any meters will have to be installed
prior to the audit
e.g. Kwh steam, oil or gas meters.
•To identify the instrumentation required for carrying out
the audit
Audit Phase:
As a first step
during the audit phase, Energy Auditor would collect the
base line data, preparation of process flow charts etc. The monitoring and
measurement will be next stage. As per the field observations, detailed
trials may be conducted for selected energy guzzlers in the
plant. Once
all the operating data and design data and other operational
practices are
collected/observed, detailed analysis of the data will have
to be done.
Based on the analyses, Energy Conservation opportunities may
be developed
and the economic viability of the options has to be
established. The study
has to properly documented and the suggestions and findings
are to be
presented to the top management
Post-Audit Phase:
In post audit phase the energy Auditor/Engineer may assist
and implement
the energy conservation recommendation measures and monitor
the performance.
3.During a ESP performance evaluation study, the inlet gas
stream to ESP is
289920NM3/hr and the dust loading is 5500 mg/ NM3. The outlet gas stream
from ESP is 301100M3/hr and the dust loading is 110
mg/NM3. How much fly
ash is collected in the system?
Based on Mass balance,
Inlet gas stream dust = Outlet Gas stream dust + Fly ash
a) Inlet gas stream flow
= 289920 NM3/hr
Dust
Concentration = 5500 mg/NM3
Inlet dust
quantity = 289920 x 5500
-----------
1000000
=
1594.50 kg/hr
b) Outlet dust quantity
= 301100 (NM3/hr) x 110 (mg/NM3)
x 1
----------
1000000
=
33.12 kg/hr
c) Fly Ash = Inlet gas stream dust – Outlet gas stream dust
=
1594.56 – 33.12 = 1561.44 kg/hr
4.Explain the following stating the advantages and
limitations if any
a)Simple Pay Back Period
b)Return on Investment
c)Internal rate of return
Simple Payback Period (SPP) represents, as a first
approximation: the time
(number of years) required to recover the initial investment
(First Cost),
considering only the Net Annual Saving:
The simple payback period is usually calculated as follows:
Examples
Simple payback period
Advantages:
A widely used investment criterion, the payback period seems
to offer the
following advantages:
•It is simple, both in concept and application. Obviously a shorter
payback generally indicates a more attractive
investment. It does not use
tedious calculations.
•It favours projects, which generate substantial cash
inflows in earlier
years, and discriminates against projects, which bring
substantial cash
inflows in later years but not in earlier years.
Limitations:
•It fails to consider the time value of money.
•It ignores cash flows beyond the payback period. This leads
to
discrimination against projects that generate substantial
cash inflows in
later years.
Return on Investment (ROI)
ROI expresses the
“annual return” from the project as a percentage of
capital cost. The
annual return takes into account the cash flows over the
project life and the discount rate by converting the total
present value of
ongoing cash flows to an equivalent annual amount over the
life of the
project, which can then be compared to the capital
cost.
Limitations:
•It does not take into account the time value of money
•It does not account for the variable nature of annual net
cash inflows.
Internal Rate of Return:
This method calculates the rate of return that the
investment is expected
to yield. The
internal rate of return (IRR) method expresses each
investment alternative in terms of a rate of return (a
compound interest rate).
popular discounted
cash flow method, the internal rate of return criterion
has several advantages:
•It takes into account the time value of money
•It considers the cash flow stream in its entirety
•It makes sense to businessmen who prefer to think in terms
of rate of
return and find an absolute quantity, like net present
value, somewhat
difficult to work with.
Limitations:
The internal rate of return figure cannot distinguish
between lending and
borrowing and hence a high internal rate of return need not
necessarily be
a desirable feature.
5.Explain in detail about Ozone Layer depletion process ad
its various effects
Ozone is highly reactive and easily broken down by man-made
chlorine and
bromine compounds.
These compounds are found to be most responsible for
most of ozone layer
depletion.
The ozone depletion process begins when CFCs (used in
refrigerator and air
conditioners) and other ozone depleting substances (ODS) are
emitted into
the atmosphere. Winds
efficiently mix and evenly distribute the ODS in the
troposphere. These
ODS compounds do not dissolve in rain, are extremely
stable, and have a long life span. After several years, they reach the
stratosphere by diffusion.
Strong UV light breaks apart the ODS molecules. CFCs, HCFCs, carbon
tetrachloride, methyl chloroform release chlorine atoms, and
halons and
methyl bromide release bromine atoms. It is the chlorine and bromine atom
that actually destroys ozone, not the intact ODS
molecule. It is estimated
that one chlorine atom can destroy from 10,000 to 100,000
ozone molecules
before it is finally removed from the stratosphere.
Effects on Human and Animal Health :
Increased penetration of solar UV-B radiation is likely to
have high impact
on human health with potential risks of eye diseases, skin
cancer and
infectious diseases.
Effects on Terrestrial Plants :
In forests and grasslands, increased radiation is likely to
change species
composition thus altering the bio-diversity in different
ecosystems. It
could also affect the plant community indirectly resulting
in changes in
plant form, secondary metabolism, etc.
Effects pm Aquatic Ecosystems:
High levels of radiation exposure in tropics and subtropics
may affect the
distribution of phytoplanktons, which form the foundation of
aquatic food
webs. It can also
cause damage to early development stages of fish,
shrimp, crab, amphibians and other animals, the most severe
effects being
decreased reproductive capacity and impaired larval
development.
Effects on Bio-geo-chemical Cycles : Increased solar UV
radiation could
affect terrestrial and aquatic bio-geo-chemical cycles thus
altering both
sources and sinks of greenhouse and important trace gases,
e.g. carbon
dioxide (CO2), carbon monoxide (CO), carbonyl sulfide (COS),
etc. These
changes would contribute to biosphere-atmosphere feedbacks
responsible for
the atmosphere build-up of
these greenhouse gases.
Effects on Air-Quality : Reduction of stratospheric ozone
and increased
penetration of UV-B radiation result in higher photo dissociation
rates of
key trace gases that control the chemical reactivity of the troposphere.
This can increase both production and destruction of ozone
and related
oxidants such as hydrogen peroxide, which are known to have
adverse effects
on human health, terrestrial plants and outdoor materials.
